Suppose you possess this kitchen appliance, then there is a greater chance that you have been through the experience of power light blinking. Is your ninja blender power-light blinking? Or is it flashing the red light? Then there is a decent chance that something is wrong with your blender. If you don’t know why the power light is blinking, then this article will be very helpful and will correctly guide you through troubleshooting it.
Common Reasons For Flashing The Power Light
There can be many reasons why the light is blinking, which, if not troubleshot on time, may cause something unfavorable.
Here we will highlight most of the Common Reasons For Flashing The Power Light in it and try to show how to solve it.
- Aligns of arrows
- Lid may be loose
- Not seated accordingly into a base
- Unclean Blender
1. Aligns of arrows
The first and foremost thing to check when your ninja blender’s light is blinking is to check the alignment of the arrows by making them face each other on both halves of the pitcher, as shown in the picture.
It may not start when it is showing the power button flashing. This implies that you really want to actually look at the arrows on the two parts of the pitcher and guarantee they are arranged accurately prior to attempting to utilize it once more.
2. The lid may be loose.
A second most common reason that more often leads to the blinking of red light in the power button is that the lid may be loose or may have become unseated, which in result causes the shutdown of the for the safety purpose.
Say, for instance, you have seen the red light blinking, then the first thing you have to do is to set the lid tightly on both sides of the pitcher and make sure it is seated tightly, not loosed.
Ensure that when you place your blender onto its base, you hear an audible snap sound telling you that it’s situated firmly set up. Moreover, if there isn’t a ticking sound, you might need to reseat the lid a couple of times before it’s appropriately situated.
3. Not seated accordingly into the base
Another normal justification for why your Ninja machine may be showing its power light, and you’re considering some solution for it, is that maybe one piece of the container isn’t snapped in as far as possible.
Your Ninja pitcher should snap effectively and solidly into the base. The front of the pitcher ought to confront you, and it should adjust or snap properly. If you notice that the power light is blazing red, be sure to check and guarantee your machine pitcher has been appropriately snapped in every way.
Check every side where they get together to make sure all that has been situated totally prior to utilizing once more. Ensure no part appears as though it’s inclining or warped either as this can prompt different issues, also like harm to the sharp blades.
Ninja blenders come well equipped with an interior warm switch that will close down your machine the moment it begins to get overheated.
In the case that your blender stops working during running, take out the switch and allow it to cool for 20-30 minutes. If the thermal switch was simply the issue, it should reset, and you will actually have the opportunity then to plug back the switch and use it normally.
The last normal reason for why your machine could streak its power light, and one which ought not to be neglected, is that maybe something is stuck inside the blender.
The most straightforward method for checking this is to eliminate the two pieces of the pitcher and investigate where they get together as well as under them. On the off chance that you see anything stuck, for example, food scraps or different articles, cautiously select those so your ninja mixture will work accurately once more!
It’s significant not to run your apparatus until it has been cleaned in light of the fact that if not, there could be further harm done which could require professional assistance to fix.
Common Mistakes To Avoid
- Beside the open top and scattered parts, there are a couple of purposes behind the Ninja Blender’s power light to streak. We often put each of the fixings into the mixture without a moment’s delay instead of taking care of an endless flow of things, bringing about the sharp edges not turning as much tension on the engine, which annihilates it over the long haul.
- When done with using it make sure to wash it properly.
- When the machine is not in working and is not in use, try to unplug it always. This can save the machine from electric shocks and is also for safety purposes.
- Don’t quickly place frozen organic products or ice into your mixture subsequent to defrosting. On the off chance that you do this, the edges of your ninja may be hurt. Defrost food that has been saved for some time prior to placing it in the blender to process. You could harm the engine or dull the edges thusly, and you’d ask why your Ninja blender’s power light is squinting when you take defrosted food from the cooler.
Assuming the power light is yet blinking odds are there’s an issue with your machine that will require fixing. The best thing to do in that circumstance is to turn off your Ninja blender from its power source and afterward plug it back in again with a gap of 10 minutes.
Assuming the power light keeps on flickering on your Ninja, you ought not to find and fix the issue yourself. Contact Ninja Customer Service for direction on the most proficient method to continue.
In conclusion, ninja blender power light flashing is typically a sign that the engine has switched off.
Remember to turn off your Ninja blender when it isn’t being used. Ultimately, don’t promptly remove frozen food sources from the cooler; defrost them prior to placing them into your Ninja blender to forestall harm!
Thank you for reading my article. Hope you enjoyed.
What if still the light is blinking after going through all the check processes?
The best answer to this is you then contact the customer service they will guide you properly, and the problem will be solved very effectively.